European Sealing Association
Klinger KLINGER top-chem 2003 2.0 mm - Printable Version

+- European Sealing Association (https://forum.bacibg.org)
+-- Forum: Flange Gaskets (https://forum.bacibg.org/forumdisplay.php?fid=1)
+--- Forum: Gasket Database (https://forum.bacibg.org/forumdisplay.php?fid=2)
+---- Forum: ESAData Approved Datasheets (https://forum.bacibg.org/forumdisplay.php?fid=10)
+---- Thread: Klinger KLINGER top-chem 2003 2.0 mm (/showthread.php?tid=200)



Klinger KLINGER top-chem 2003 2.0 mm - AMTEC - 03-27-2023

Approval of new Datasheet

Type:        Sheet Gasket
Material:   PTFE

Cross-check: The PQR values at low stresses and RT are higher than the old values on gasketdata.org. Therefore, we recommend a PQR test at  10 or 20 MPA @ RT.


RE: Klinger KLINGER top-chem 2003 2.0 mm - Donit - 03-27-2023

Agree with cross check test: Pqr at 10 MPa and RT.


RE: Klinger KLINGER top-chem 2003 2.0 mm - SGL - 03-27-2023

I am fine with the suggested cross check.


RE: Klinger KLINGER top-chem 2003 2.0 mm - Garlock - 03-27-2023

Dear Colleagues,
Datasheet to me ALL-in ALL sems to be fine, without any need to cross-Check.

But few comments from my side with regards to "old" datasheets from my side.
1) Revisions 1&2 do show higher creep at 80MPa load 0,3mm higher creep (les thicknes) than mentioned in the new datasheet idoes differ.
2) Revisions 1&2 do show better sealability result (more or les one decade better) than the latest revision now does show.
--> With revision3 (published 2013) at 10bar line pressure with 10MPa Load, Sealability level of L0,01 could be reached at 10MPa (and 7MPa needed to upheld).     With line pressure of 10bar and 20MPA assembly load L0,0001 could be reached. At 40 bar line pressure with 20MPa assembly load, L0,01 could be reached at 16MPa loading (and 10MPa to upheld): 

--> now with the latest revision sealability is more than 1decade differrent. At 10bar line pressure with 10MPa assembly load only L0,1 and with 20MPa assembly load only L0,001 can be reached. With 40bar line pressure an 10MPa assembly load only L0,1 and with 20MPa assembly load only L0,01 can be reached. In order to reach L0,01 

--> at 28MPa assembly load and 40bar line pressure revisions 1&2 did allow L0,0001 to be reached, now L0,01 still is present or L0,001 is hardly reached.

This does look more like a 3,2mm datasheet to me than like a 2,0mm thickness.
Never the les the data in my eyes looks stringent and no need for re-test in my eyes.
Best wishes, RALF


RE: Klinger KLINGER top-chem 2003 2.0 mm - Montero - 03-27-2023

In my experience is very common to find a PQR improvement followed by a sealability loss (always in tolerance for a same quality/composition).
But I agree with the cross check suggested.


RE: Klinger KLINGER top-chem 2003 2.0 mm - Frenzelit - 03-30-2023

We are fine with the suggested cross check.


RE: Klinger KLINGER top-chem 2003 2.0 mm - AMTEC - 05-23-2023

Cross-check:
In the cross-check of PQR @ 10 MPa/RT the data submitted by Klinger were confirmed.