European Sealing Association
GORE® Universal Pipe Gasket 6.0mm - Printable Version

+- European Sealing Association (https://forum.bacibg.org)
+-- Forum: Flange Gaskets (https://forum.bacibg.org/forumdisplay.php?fid=1)
+--- Forum: Gasket Database (https://forum.bacibg.org/forumdisplay.php?fid=2)
+---- Forum: ESAData Approved Datasheets (https://forum.bacibg.org/forumdisplay.php?fid=10)
+---- Thread: GORE® Universal Pipe Gasket 6.0mm (/showthread.php?tid=45)



GORE® Universal Pipe Gasket 6.0mm - root - 01-06-2020

Approval of Data Import from gasketdata.org

Type: sheet gasket
Publication: 01/25/16

Material: PTFE

Link to gasketdata.org


RE: GORE® Universal Pipe Gasket 6.0mm - SGL - 06-22-2020

Leakage at 40 bar (for unloading to 5 MPa the divergence in the measured leak rates is too high): ESAdata specification allows the following procedure in 5.4.2: "If a value (typically at the end of the graph, e. g. the 5 MPa unloading leakage value) is outside of the allowable divergency, one possibility to accept the rest of the values is to delete this value"
I spoke to Daniel Bissett (GORE). He would be fine with this approach. To make it look better it makes sense not only to delete the 5 MPa unloading value for QA 30, 40 and 80 MPa, but also for 60 MPa.
If these values are deleted, my vote changes from "no" to "yes".


RE: GORE® Universal Pipe Gasket 6.0mm - Teadit - 06-22-2020

Double check on PQR Room Temperature 10MPa, because divergence is too big.


RE: GORE® Universal Pipe Gasket 6.0mm - Klinger - 06-22-2020

All submitted GORE UPG show increase in leakage beginning at 60MPa rather than getting tighter. This might indicate destruction of gasket.I propose x check of qsmax RT with visual inspection of gasket.


RE: GORE® Universal Pipe Gasket 6.0mm - AMTEC - 09-30-2020

The following cross-check is recommended:

PQR at 10 MPa/RT

Comment to the other replies of the Task force:
Klinger: The increasing of the leak rate at gasket stress levels above 60 MPa is probably caused by too short measuring times. The characteristics are not influenced by this behavior.
SGL: During the unloading to 5 MPa a behaviour like a blow-out occurs. Gore is contacted to either delete these values or to adapt them to the higher leak rate of the double test. If the higher leak rates are used, the gasket characteristics are more or less identical.

Result of the cross-check is within the acceptable divergence range. Therefore the datasheet is accepted.


RE: GORE® Universal Pipe Gasket 6.0mm - IDT - 10-01-2020

I also suggest a cross-check PQR at RT/10 MPa...


RE: GORE® Universal Pipe Gasket 6.0mm - AMTEC - 10-05-2020

(06-22-2020, 02:07 PM)SGL Wrote: Leakage at 40 bar (for unloading to 5 MPa the divergence in the measured leak rates is too high): ESAdata specification allows the following procedure in 5.4.2: "If a value (typically at the end of the graph, e. g. the 5 MPa unloading leakage value) is outside of the allowable divergency, one possibility to accept the rest of the values is to delete this value"
I spoke to Daniel Bissett (GORE). He would be fine with this approach. To make it look better it makes sense not only to delete the 5 MPa unloading value for QA 30, 40 and 80 MPa, but also for 60 MPa.
If these values are deleted, my vote changes from "no" to "yes".

We studied the influence of the divergence in the leak rates during these unloading steps. We determined that a higher divergence has only a marginal influence on the characteristics, if the leak rate is increasing by a factor of 100 or more ("blow-out") compared to the leak rate in the previous gasket stress level.


RE: GORE® Universal Pipe Gasket 6.0mm - Donit - 10-06-2020

(09-30-2020, 03:58 PM)AMTEC Wrote: The following cross-check is recommended:

PQR at 10 MPa/RT

Comment to the other replies of the Task force:
Klinger: The increasing of the leak rate at gasket stress levels above 60 MPa is probably caused by too short measuring times. The characteristics are not influenced by this behavior.
SGL: During the unloading to 5 MPa a behaviour like a blow-out occurs. Gore is contacted to either delete these values or to adapt them to the higher leak rate of the double test. If the higher leak rates are used, the gasket characteristics are more or less identical.

Result of the cross-check is within the acceptable divergence range. Therefore the datasheet is accepted.
The cross-check test was requested because the difference between two tests was too high.
Now we have three results. 0.71; 0.78; 0.71 - I would say, that the Pqr value is 0.71 and not 0.75 as it is the mean value of first two tests. Value 0.78 seems to be too high.