![]() |
|
IDT Corrugated metallic gasket with graphite layer, WD10, WS1.4571/3803 3 mm - Printable Version +- European Sealing Association (https://forum.bacibg.org) +-- Forum: Flange Gaskets (https://forum.bacibg.org/forumdisplay.php?fid=1) +--- Forum: Gasket Database (https://forum.bacibg.org/forumdisplay.php?fid=2) +---- Forum: ESAData Approved Datasheets (https://forum.bacibg.org/forumdisplay.php?fid=10) +---- Thread: IDT Corrugated metallic gasket with graphite layer, WD10, WS1.4571/3803 3 mm (/showthread.php?tid=93) |
IDT Corrugated metallic gasket with graphite layer, WD10, WS1.4571/3803 3 mm - root - 01-06-2020 Approval of Data Import from gasketdata.org Type: corrugated flat or grooved metallic and filled metallic gaskets Publication: 18.06.2012 Material:GR Link to gasketdata.org RE: IDT Corrugated metallic gasket with graphite layer, WD10, WS1.4571/3803 3 mm - Teadit - 07-28-2020 E-Modulus looks weird but have too little experience for this gasket type to decide and will abstain. RE: IDT Corrugated metallic gasket with graphite layer, WD10, WS1.4571/3803 3 mm - Frenzelit - 08-05-2020 PQR values 500°C / 10 and 20 MPa much higher compared to PQR 400°C ; crosscheck PQR 500°C and 20 MPa is required RE: IDT Corrugated metallic gasket with graphite layer, WD10, WS1.4571/3803 3 mm - Klinger - 08-05-2020 at 40bar and 40MPa tightness is 1.09E-05 at 25bar and 40MPa tightness is 1.08E-04 the higher the internal pressure the tighter the gasket? I may proposse a x-check @ 40 bar RE: IDT Corrugated metallic gasket with graphite layer, WD10, WS1.4571/3803 3 mm - Donit - 08-11-2020 (07-28-2020, 11:10 AM)Teadit Wrote: E-Modulus looks weird but have too little experience for this gasket type to decide and will abstain.In the first test at 100°C there is a pick at 140 MPa. Based on my experience this is not an expected phenomenon. ¸I assume the reason is in the measurement. In such a case I would repeat the test, but this is a decision of the manufacturer. (08-05-2020, 12:28 PM)Frenzelit Wrote: PQR values 500°C / 10 and 20 MPa much higher compared to PQR 400°C ;The test results at 500°C look as they were performed later on other set of gaskets. Agree with proposed crosscheck. (08-05-2020, 05:40 PM)Klinger Wrote: at 40bar and 40MPa tightness is 1.09E-05Agree. RE: IDT Corrugated metallic gasket with graphite layer, WD10, WS1.4571/3803 3 mm - AVKO - 08-12-2020 Looking the Leak Rates at 80 bar: At 80MPa/80bar for the first test the result is 1,15E-05 On the second test the result is 8,54E-06 (???) At 100MPa/80bar first test shows 8,69E-06 Second one 1,09E-05 I believe that those are swapped, so perhaps a cross check is really necessary, or at least a good review on all submitted table data. Perhaps a x-check will be easier and more reliable RE: IDT Corrugated metallic gasket with graphite layer, WD10, WS1.4571/3803 3 mm - AMTEC - 10-06-2020 Cross-check was requested for tests at 500 °C. Also test result of the leakage test at 25 bar (which was not published on gasketdata.org) fits not to the results at 40 bar. IDT was contacted and they decided that only the characteristics which were published on gasketdata.org should be transferred to the ESA database. This means that the values @ 500 °C and the leak rates @ 25 bar are not considered. RE: IDT Corrugated metallic gasket with graphite layer, WD10, WS1.4571/3803 3 mm - Donit - 10-06-2020 I suggest to omit the Eg value of the first test at 140 MPa and 100°C as it is possible according to prEN13555:2019. This value is not logical. |